Automatic Wrinkle Recovery Tester
The main principle of the wrinkle recovery tester is to apply a predetermined pressure to the specimen under standard atmospheric conditions and to maintain the specified time. The overall structure of the instrument and the precise spiral column ensure that the loaded specimens produce a uniform deformation. After removing the sample from the instrument, re-adjust the sample under standard atmospheric conditions and allow it to recover for a certain period of time, and then compare the sample with the reference sample to assess the appearance of the sample.
The instrument consists of a base with a bracket, the base of the fixed steel plate and the top of the movable steel plate to match ,the activities of the flange with the locking pin. Equipped with four standard weights, respectively, 2000g, 1000g, 500kg, 200kg.
Application
The instrument consists of a base with a bracket, the base of the fixed steel plate and the top of the movable steel plate to match ,the activities of the flange with the locking pin. Equipped with four standard weights, respectively, 2000g, 1000g, 500kg, 200kg.
Application
The wrinkle recovery test instrument detects the recovery of the specimen after a certain period of time under a load. It is suitable for any fiber pure or blended fabric test. Besides, it can not maintain the shape of stable materials under the characteristics of the conditions, such as the material which is soft, thin and easy to bend. We can evaluate its anti-crease performance through this device.
Technical Parameters
Standard weights（2000g、1000g、500kg、200kg）
Full set 5 inch x 3 inch (5 / set)
The rating card (optional)
Standards:
AATCC 128 Wrinkle recovery of fabrics: Appearance method
ISO 9867 Textiles - Evaluation of the wrinkle recovery of fabrics - Appearance method
ENKA 3061
ISO 9867 Textiles - Evaluation of the wrinkle recovery of fabrics - Appearance method
ENKA 3061
Accessories:
(1)First ,use the pressure sample device, three samples are tested continuously. The interval is about 1min;
(2)Fold the sample face to face. Cloth edge clip with a clip, not more than 5mm;
(3)In some cases the sample surface will be stained together. We should use a piece of paper or aluminum foil whose size is 18x14mm. Be careful not to contact the sample by hand;
(4)Place the folded sample between the two briquettes and apply the weight immediately. Turn on the chronograph and wait 60 + 2 seconds. Prepare the next sample according to 2,3,4 steps.
(5)After 5 minutes, remove the first piece of weight quickly and easily. Transfer the folded sample with the clip to the sample rack of the measuring instrument;
(6)Remove the paper or aluminum foil. Place one side of the sample in the sample holder and the other side is the free hanging. After 60 +2 seconds, Put the second and third pieces of samples into the sample folder;
(7)Adjust the instrument so that the hanging end of the sample is consistent with the vertical mark of the instrument, within 5min should be constantly adjusted (so that the hanging end of the sample is consistent with the vertical mark of the instrument,) to avoid the impact of gravity;
(8)After 5 minutes, record the recovery angle of the sample. If the sagging side is slightly curled or twisted to pass through the vertical plane of the center of the droop and the axis of the dial as a reference for the crease return angle reading;
(9)Repeat the above steps, and then do three negative fold of the sample and the zonal frontal fold and the opposite fold (a total of 12).
(2)Fold the sample face to face. Cloth edge clip with a clip, not more than 5mm;
(3)In some cases the sample surface will be stained together. We should use a piece of paper or aluminum foil whose size is 18x14mm. Be careful not to contact the sample by hand;
(4)Place the folded sample between the two briquettes and apply the weight immediately. Turn on the chronograph and wait 60 + 2 seconds. Prepare the next sample according to 2,3,4 steps.
(5)After 5 minutes, remove the first piece of weight quickly and easily. Transfer the folded sample with the clip to the sample rack of the measuring instrument;
(6)Remove the paper or aluminum foil. Place one side of the sample in the sample holder and the other side is the free hanging. After 60 +2 seconds, Put the second and third pieces of samples into the sample folder;
(7)Adjust the instrument so that the hanging end of the sample is consistent with the vertical mark of the instrument, within 5min should be constantly adjusted (so that the hanging end of the sample is consistent with the vertical mark of the instrument,) to avoid the impact of gravity;
(8)After 5 minutes, record the recovery angle of the sample. If the sagging side is slightly curled or twisted to pass through the vertical plane of the center of the droop and the axis of the dial as a reference for the crease return angle reading;
(9)Repeat the above steps, and then do three negative fold of the sample and the zonal frontal fold and the opposite fold (a total of 12).
Technical Parameters
| Items | Parameters< /span> |
| Sample size | 15cm×28cm(6×11inch) |
| Weights | 2000g，1000g，500kg，200kg Accumulate |
| Dimensions | 150×150×330mm(L×W×H)< /span> |
| Weight | 9.5kg(21lb) |
Full set 5 inch x 3 inch (5 / set)
The rating card (optional)
Localisation : No. 2578 Minhang District Gu Dai Road, Shanghai, 201199 Shanghai,
Personne à contacter : Sun Qin, +86 21 6780 0179
Personne à contacter : Sun Qin, +86 21 6780 0179
Bonne affaire : acheter au vendeur
Consultez notre guide pour effectuer une transaction en toute sécurité ! En aucun cas Algomtl ne peut être tenu responsable des annonces publiées. Seule la responsabilité du vendeur ou de l'acheteur en cas de litige est engagée.
Nous vous invitons à lire nos conditions générales d'utilisations. Vous pouvez aussi vous rendre sur nos FAQ et consulter notre page d'informations sur les risques liés à la contrefaçon.
Nous vous invitons à lire nos conditions générales d'utilisations. Vous pouvez aussi vous rendre sur nos FAQ et consulter notre page d'informations sur les risques liés à la contrefaçon.
|
Cette page concerne les importateurs et exportateurs de Automatic Wrinkle Recovery Tester Rechercher dans la catégorie : Biens d'équipement Rechercher dans la catégorie : recovery, tester, wrinkle, automatic |
France 
93000 Bâtiment
93000 BâtimentSignalez un abus
Thursday 30 May 2013
Quantité : 1000000 to - Prix : 10€
Matériau "Énola" - une expérience unique et inégalée dans le monde; Matériau de construction constitué de polystyrène expansé, de ciment et des additifs spéciaux, qui sont le savoir-faire de notre entreprise. Les représentants de plusieurs pays étrangers s'intéressent de plus en...
Agent commercilae
- basarabia
- 93000 - Bobigny
- +33 6 21 86 25 35
Pologne 
43-100 Pro / B2B
43-100 Pro / B2BSignalez un abus
Friday 19 December 2014
La société Infolab Narloch Spolka Jawna est au cours d'implémenter son produit "Le logiciel tachospeed" au Nord-Afrique et nous sommes à la recherche d'un revendeur/distributeur du logiciel. Depuis plus de 10 ans, Tachospeed est la solution la plus populaire pour la lecture automatisée...
Infolab Narloch Sp.j
- 43-100 - Tychy
- +48 3 27 50 50 06
- +48 5 03 51 01 38
Espagne 
30410 Alimentaire
30410 AlimentaireSignalez un abus
Thursday 08 October 2015
Quantité : Mini 24T - Prix : 355 à 618 Euros/Tonn
PRESTIGE FORCE Aliment floconné complet en complément de la ration de volume pour chevaux et poneys de sport au travail moyen à intense. Quantité de 0.5 – 1.5 Kg d'aliment pour 100 Kg de poids, en fonction de l'âge, de la taille et de l'activité du cheval. Répartir au minimum...
Agrofood Ganados
- 30410 - Murcia
- +34 9 68 10 66 28
- +34 6 72 36 35 29
Paiement sécurisé
