Algomtl
svgfair.com
 
Mass Airflow Sensors
Détails
Chine (Rép. pop) Destockage
Destockage

Mass Airflow Sensors

The automotive mass air flow sensor, also known as the airflow meter, converts the inhaled airflow into an electrical signal and sends it to the ECU, which is one of the basic signals for determining fuel injection. It is a sensor for measuring the airflow inhaled into the engine and one of the important sensors of the EFI engine.
How maf mass air flow sensor is working? The air sucked by the air filter rushes to the valve, and the valve stops when it turns to the position where the air intake is balanced with the return spring, that is, the opening of the valve is directly proportional to the air intake. A potentiometer is also installed on the rotating shaft of the valve. The sliding arm of the potentiometer rotates synchronously with the valve. The voltage drop of the sliding resistance is used to convert the opening of the measuring piece into an electrical signal, which is then input into the control circuit.
The mass air flow sensor from MAPMS auto sensors has the advantages of minimal pressure loss and a large measurable flow range.
Mass Airflow Sensors Features
Accurately measure engine air intake quantity.
Accurately control the fuel injection quantity.
Form the best fuel-air ratio.
Minimal pressure loss and large measurable flow range.
What Are the Symptoms of a Bad Mass Airflow Sensors ?
In order to obtain the best concentration of mixture under various operating conditions, the amount of air sucked into the engine at each moment must be measured correctly as the main basis for ECU to control fuel injection. These are fault symptoms in the following for MAF Sensor.
Poor Engine Acceleration
Poor Engine Acceleration. When the deviation of the output signal of the mass air flow sensor is not enough for the ECU to record the fault code, as the air flow signal can not accurately reflect the actual air intake, the fuel injection amount controlled by the ECU is too small, so the engine speed does not rise but falls.
Cause
For EFI engine with hot film mass air flow sensor, ECU judges the amount of intake air and determines the amount of fuel injection according to the current flowing through the hot film resistance, so as to meet the needs of different working conditions of the engine. If dust accumulates on the hot film to form a thermal insulation layer, once the air inlet becomes larger, the temperature change slows down, the required current becomes smaller, and the fuel injection quantity determined by ECU will be reduced. At this time, the actual air intake is relatively large, resulting in too thin mixture, which eventually leads to engine idling jitter and "tempering" during rapid acceleration.
The Automatic Transmission Will Not Upshift to Overdrive
The automatic transmission cannot be raised to the overdrive gear. If the mass air flow sensor is short circuited to the ground, the mixture will be too thin, which will reduce the output power of the engine, and the automatic transmission will not be able to rise to the overdrive gear.
Now the mass airflow sensor price is reasonable, if you have needs to buy high quality mass airflow sensors, please leave us a message.

As one of car spares suppliers, we can offer sorts of auto spares sale, if you are interested, please contact us.

Localisation : Room 1505, F15, Bldg T2, 2 Yichuang St, Huangpu 510555, Guangzhou, China, 510555 Guangzhou,
Personne à contacter : MAPMS MAPMS, +86 139 2617 0287

Bonne affaire : acheter au vendeur

Consultez notre guide pour effectuer une transaction en toute sécurité ! En aucun cas Algomtl ne peut être tenu responsable des annonces publiées. Seule la responsabilité du vendeur ou de l'acheteur en cas de litige est engagée.
Nous vous invitons à lire nos conditions générales d'utilisations. Vous pouvez aussi vous rendre sur nos FAQ et consulter notre page d'informations sur les risques liés à la contrefaçon.
Cette page concerne les importateurs et exportateurs de
Mass Airflow Sensors

Rechercher dans la catégorie : Destockage
Rechercher dans la catégorie :
sensors, mass, airflow
France 59590 Pro / B2B
Robinet à soupape - Corps Acier à soufflet Inox

Wednesday 14 September 2016

Quantité : 5000 - Prix : 100,00 €

Corps Acier A216 WCB & GS-C25 & 1.0619 & GP240GH - Clapet Inox 420 - Siège Inox 420 - Soufflet Inox 321 - Presse étoupe Graphite Tige et volant montants tournants - Chapeau et presse étoupe boulonnés - A brides RF PN16/ PN25/40 - Commande par volant fonte - Peinture...

ETM Armaturen

  • 59590 - Henri Durre
  • 86 577 67953935
France 59590 Pro / B2B
Robinets à soupape

Wednesday 14 September 2016

Quantité : 5000 - Prix : 50,00 €

Robinet à soupape PN 16/25/40 Acier moulé - Robinet à soupape PN 25‑40 - Construction suivant DIN 3356 - Diamètre : DN15 à DN300 - Chapeau boulonné à arcade - Presse-étoupe boulonné - Tige montante à filetage extérieur - Ecartement suivant EN 558‑1 Série 1 - Raccordement...

ETM Armaturen

  • 59590 - Henri Durre
  • 86 577 67953935
Bulgarie 1407 Pro / B2B
Recherche de distributeur en Afrique par fabricant bulgare de lubrifiants et graisses...

Tuesday 18 August 2026

Quantité : par conten

Recherche de distributeurs Prista Oil Holding est une entreprise bulgare certifiée ayant pour activité principale la production (blending) et le commerce de lubrifiants, de graisses et de fluides spéciaux pour toutes sortes d'applications dans les domaines de l'automobile et de l'industrie...

Prista Oil

  • 1407 - Sofia
  • 00 359 888 888 984
 

Paiement sécurisé

Paiement sécurisé

Informations

Les plus recherchés